Solar Beam Security – Homestead, FL

CALL US TOLL FREE TODAY 877.737.2326

Email

Password

Forgot Password?

SOLARBEAM POWER VOLTAGE CONTROLLER

PV CONTROLLER - SBPV1812

THE SOLARBEAM PV CONTROLLER IS DESIGNED TO MONITOR ALL FUNCTIONS OF THE SOLARBEAM TOWER. IT CAN BE POWERED BY SOLAR OR ELECTRICAL SUPPLY PROVIDING CHARGING TO THE BATTERIES AND POWER TO THE LOAD. IN THE EVENT A FAULT OCCURS, YELLOW LED LIGHTS WILL TURN ON AND THE RELAY CIRCUIT WILL ACTIVATE TO ALERT RADIO UNIT OR SERVICE LIGHT.

SOLARBEAM PV CONTROLLER - NORMAL OPERATION FEATURE

THE SOLARBEAM PV CONTROLLER IN IT’S NORMAL OPERATION MODE WILL SHOW A GREEN LIGHT ON INDICATING THE BATTERIES ARE FULLY CHARGED. THE GREEN LIGHT BLINKING INDICATES THE PV CONTROLLER IS CHARGING THE BATTERIES, ONCE THE BATTERIIES ARE CHARGED THE GREEN LIGHT WILL TURN TO SOLID GREEN. IF THE GREEN LIGTH IS "OFF" NO POWER UNPUT IS RECONNIZED FROM A/C OR SOLAR.

SOLARBEAM PV CONTROLLER - FAULT RELAY OUTPUT FEATURE

THE SOLARBEAM PV CONTROLLER IS DESIGNED TO MONITOR ALL FUNCTIONS OF THE SOLARBEAM TOWER, SHOULD ANY OF THE 1-10 FAULT LIGHT(S) ARE ACTIVATED, A FAULT RELAY WILL BE TRIGGERED AS SHOWN BELOW. THE FAULT RELAY WILL PROVIDE TWO FUNCTIONS, ONE FUNCTION WILL TRIGGER THE FORM "C" RELAY AND THE OTHER FUNCTION WILL TURN ON A LIGHT, SUCH AS A REMOTE LIGHT MOUNTED ON THE OUTSIDE OF THE TOWER THAT WILL ALERT THE CLIENT SERVICE IS NEEDED.

SOLARBEAM PV CONTROLLER - POWER INPUT FEATURE

THE SOLARBEAM PV CONTROLLER CAN BE POWERED BY SOLAR OR ELECTRICAL SUPPLY PROVIDING CHARGING TO THE BATTERIES AND POWER TO THE LOAD. IN THE EVENT A FAULT OCCURES, YELLOW LED LIGHTS WILL TURN ON AND THE RELAY CIRCUIT WILL AVTIVATE TO ALERT RADIO UNIT OR SERVICE LIGHT.

SOLARBEAM PV CONTROLLER - BATTERY FEATURE

THE SOLARBEAM PV CONTROLLER IS DESIGNED TO CHARGE THE BATTERIES AND POWER THE LOAD. THE PV CONTROLLER IS CAPABLE OF CHARGING UP TO EIGHT (8) BATTERIES TOTALING (96AMPS) OF POWER CAPACITY. GENERALY, THE SOLARBEAM TOWER UTILIZES ONLY FOUR BATTERIES (48AMPS), HOWEVER, ADDITIONAL BATTERIES MAY BE ADDED FOR SPECIAL APPLICATIONS, IF DESIRED.

THE PV CONTROLLER IS DESIGNED TO CHARGE EACH BATTERY INDIVIDUALLY, IN THE EVENT A BATTERY MALFUNCTIONS, SUCH AS A LOW BATTERY OR A POTENTIAL DEFFECTIVE BATTERY, THE FAULT LIGHT AND FAULT RELAY WILL BE ACTAVATEDAS SHOWN BELOW WITH THE RED #2 BATTERY.

IF THE BATTERY IS UNABLE TO HOLD A CHARGE, OR DRAINS BELOW THE NORMAL OPERATING VOLTAGE, THE FUALT LIGHT WILL BE ACTIVATED.

IF ONLY FOUR BATTERIES ARE USED INSTEAD OF EIGHT BATTERIES, YOU WILL NEED TO RUN A JUMBER WIRE BETWEEN B1a & B1b, B2a & B2b, B3a & B3b AND B4a & b4B IN ORDER TO BYPASS THE FAULT LIGHT.

SOLARBEAM PV CONTROLLER - LOAD FEATURE

THE SOLARBEAM PV CONTROLLER IS DESIGNED TO MONITOR ALL FUNCTIONS OF THE LOAD OUTPUT CIRCUIT. IN THE EVENT THE BATTERIES DRAIN BELOW THE GIVEN VOLTAGE, THE OUTPUT CIRCUIT WILL DISCONNECT.

BECAUSE IT’S POSSIBLE THE SOLAR OR A/C SUPPLY CAN BECOME DISCONNECTED, THE LOAD MAY DRAIN THE BATTERIES DEAD. FOR THIS REASON, A DROP-OUT CIRCUIT WILL DISCONNECT THE INDIVIDUAL LOAD OUTPUT(S). ONCE THE POWER INPUT IS RESTORED, THE BATTERIES WILL RECHARGE AND THE LOAD OUTPUT CIRCUIT(S) WILL RE-INSTATE THE POWER TO THE LOAD.

FOUR LEVELS OF LOAD DISCONNECT IS AVAILABLE, THE FIRST CIRCUIT TO DROP-OUT WILL BE THE L4 - LOAD CIRCUIT (AUX, IR LIGHTS,HEATER,ETC.), DISCONNECTING AT 11.5 VOLTS.

THE SECOND CIRCUIT TO DROP-OUT WILL BE L3 - LOAD CIRCUIT, DISCONNECTING AT 11VOLTS (UPPER BEAMS). THE THIRD CIRCUIT TO DROP-OUT WILL BE THE L2 - LOAD CIRCUIT , WHICH WILL DROP-OUT AT 10.5VOLTS (LOWER BEAMS). LAST, THE FOURTH CIRCUIT TO DROP-OUT WILL BE THE E1 - EMERGENCY CIRCUIT, AT 9.5VOLTS. WHICH IS USED FOR THE RADIO ONLY.

SHOULD ANY OF THE FOUR DROP-OUT CIRCUITS DISCONNECT, THE FAULT LIGHT AND FAULT RELAY WILL BE ACTIVATED.

HOME ABOUT US PRODUCTS APPLICATIONS SERVICES NEWS DEALERS CONTACT US